Home > Error Code > Whirlpool Washer Error Codes F21

Whirlpool Washer Error Codes F21

Contents

It will try to unlock the door 6 times before displaying the error. After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. If there are no stored errors 888 will be displayed with 3 beeps. This should clear the unit of the excess detergent. 1. http://techkumar.com/error-code/whirlpool-top-load-washer-error-codes.html

The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. Make sure that both valves at the water source(s) are turned on all the way. 2. Unplug the washer for 5 minutes, restore power and see if the code clears. George Vassallo 79,941 views 10:33 Whirlpool , KitchenAid & Kenmore Washer is leaking and has a loud spin - GHW9400PW4 - Duration: 57:28.

Whirlpool Washer Error Codes F21

The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Verify there is not a siphon problem. 3. Plug in washer or reconnect power. 4. If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1.

or it's affiliates. Press 'Stop/Cancel' to clear display. Press PAUSE/CANCEL twice to clear the display. Whirlpool Top Load Washing Machine Error Codes Check/clean drain pump filter of foreign objects. 5.

Check the drive system for any worn or failed components. 4. Whirlpool Top Load Washer Error Codes F03 HEATER SC TO GROUND The Heater has a internal short circuit. I had so many questions and they answered them all." Sharon S. you could try here Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU).

rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. Whirlpool Duet Reset If too much detergent was used: – Run the unit through a RINSE/SPIN cycle. – Run a NORMAL cycle without adding any detergent. Press and HOLD start to continue the cycle, or press 'Stop/Cancel' to clear display and cancel cycle. NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed.

  • Replace the Motor Control Unit.
  • Replace control.
  • F03 HEATER SC TO GROUND The Heater has a internal short circuit.
  • Door switch open while door is locked. 1.
  • Check Pressure Switch for correct working with a DVM/VOM. 3.

Whirlpool Top Load Washer Error Codes

Check sensor, sensor harness and sensor harness connection at sensor and oven control. http://www.appliancehelponline.com/whirlpool.html Press STOP/CANCEL to clear the display. Whirlpool Washer Error Codes F21 Close Thank you! Whirlpool Duet Dryer Error Codes F14 EEPROM error The Central Control Unit (CCU) receives it’s data from an EEPROM onboard the CCU.

If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. weblink SamuraiRepairman 89,676 views 5:10 WHIRLPOOL DUET / MAYTAG WASHER MACHINE repair error codes F01,F06,E01,E02 - Duration: 3:15. If the condition continues four times, the F31 code will show.MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will F7 - Function Key Stuck - Replace control board (clock). Whirlpool Washing Machine Error Codes E1

If there are no problems, you usually need to replace the door lock assembly. Check doorswitch system. (See checklist of F26 and F29). Potential Causes • Check the Water Temperature Sensor, Heating Element and Element Relay • Check connections to the Sensor, Heating Element and Relay Replace failed component. http://techkumar.com/error-code/f02-error-code-whirlpool-washer.html Plug in washer or reconnect power. 6.

Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. Whirlpool Dryer Error Codes F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed. F5 faults are door lock and door switch related duet codes.

This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain

SamuraiRepairman 41,681 views 2:15 How To Remove The MCU From A Whirlpool Duet WFW (Kenmore, Amana, & Maytag Epic Included) - Duration: 9:57. Push the door and check if it is completely closed. 2. Unplug the unit to service. Whirlpool Washer Error Codes A10 The failure will be reset after running the Diagnostic Test Program. 1.

SL Suds lock The motor controller senses a suds lock condition by analyzing the current draw on the drive motor. Watch Queue Queue __count__/__total__ Find out whyClose Whirlpool Fault Codes Harold Jackson SubscribeSubscribedUnsubscribe144144 Loading... F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure his comment is here Check the drive system for any worm or failed components and reconnect power and plug unit in.

FdU Door unlock error A Door Unlock Error occurs if the door cannot be unlocked. Plug in washer or reconnect power. 4. Unplug washer or disconnect power. 2. ... Door switch/lock unit failure. 1.

After you have recorded any stored errors you can clear the code by pressing and holding the 3rd diagnostics button for 5 seconds. Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. F8 Board failure Replace control board (also called ERC or clock). Plug in washer or reconnect power. 6.

F5 - E6 Door is open, but latch is locked F5 - E7 Self clean latch will not unlock F6 - E0 Return line not connected If switch pulse return line Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, F07 Motor control unit error The Central Control Unit has detected a short in the motor control unit. Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4.