Home > Error Code > Whirlpool Duet F27 Error Code

Whirlpool Duet F27 Error Code

Contents

Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Check the water temperature sensor and connection to it. 3. Is there a way to remove the drain motor and make sure it is clean? Model # wfw8300sw00. If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1. this contact form

The pressure switch is very rare to fail so the first thing to check is that the hose is not pinched closed and doesn't have any holes in it. Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). 4. F09 Overflow condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. Unplug washer or disconnect power. 3. http://www.shopyourway.com/questions/1087402

Whirlpool Duet F27 Error Code

CA or CI Average current limit or Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). 4. Replace CCU board. If the Overflow contact on the pressure switch is closed for more than 60 seconds an Overflow condition will occur.

  1. NOTE: The door switch/lock unit can be manually unlocked.
  2. Liqidarts 3.906 visualizaciones 2:13 F11 Whirlpool Duet Washer - How to Fix - Duración: 7:06.
  3. If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1.
  4. F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1.
  5. The wires should be to the left when facing the MCU connectors.
  6. ob Off balance If the motor controller detects an unrecoverable off-balance condition, the machine controller will shut down and display an "ob" for off balance.

Unplug washer or disconnect power. 8. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. You can't post conmments that contain an email address. × Comment Anonymously Video Images Related Topics: Kenmore Elite 45986 Front Load... Whirlpool Washer F23 HEATER FAILURE If the temperature increase during the first 40 minutes is less than 86°F (30°C). 1.

Check the inlet valve for proper shut off.7. The shop vac method works great for this. Replace probe if all else checks out ok. Answer questions, earn points and help others Answer questions × Add an image: My Computer Web Address Search Add an Image from Your Computer: You can upload a JPG, GIF, or

Refer to the Water Temperature Sensor section. fb.me/OqBz8UpJ 5daysago ASTI 2017 Feb 8-11, 2017 save the date! And the truth shall make you free. Very good information by the way.

F27 Error Code Kenmore

Until we 11/1/2016 11/1/2016 centralappliance1 When putting my stove on clean, it comes up with F9 error, 11/1/2016 11/1/2016 woody463 X Ask an Appliance Technician Get a Professional Answer. 100% Satisfaction http://applianceassistant.com/Washer-Repair/Duet-Washer-2nd-Gen/Duet-Washer-Error-Codes.php All rights reserved. Whirlpool Duet F27 Error Code If all the buttons seem to be working then you likely have a main control board problem. Whirlpool Front Load Washer Error Codes All this data exchange is fact-checked and verified by a process called “handshaking” (yes, that’s what it’s really called).

Unplug washer or disconnect power. 2. weblink Inicia sesión para añadir este vídeo a una lista de reproducción. If the condition continues four times, the F31 code will show. 1. Good luck Oct 02, 2009 | Whirlpool Duet GHW9150P Front Load Washer 7 Answers F21 Error Code on Whirlpool Duet & Kenmore Elite Front Loader Washers This fixed my problem exactly! Whirlpool 6th Sense Washing Machine Error Codes

F/05 Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, Check the MCU by looking for operations of the drive motor. 7. F2 will appear. http://techkumar.com/error-code/whirlpool-duet-washer-error-code-f06-e02.html Replace motor controller.

Unplug washer or disconnect power for two minutes. F26 Door Switch Error Possible causes… 1. Check all hoses for possible leaks. 6.

Place a bucket or pan underneath it since you will get the water spilling out of there.

PUMP DRIVE ERROR The pump driver fails to activate. Reply Nate says: April 7, 2016 at 10:21 pm Nearly all front load washers and other appliances nowadays are designed and built to be utter garbage. Check the Duet Washer Motor. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. The failure will be reset after running the Diagnostic Test Program. heres the part you turn. his comment is here Verify there is not a siphon problem. 2.

The Steamer will no longer function for any wash cycle and should be replaced. Follow ApplianceAssistant on Twitter! Today i drained it, took everything off and cleaned it that I could possibly find and I am now getting an F27 Error. F11 Serial communication error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

Verify CCU operation by running a Diagnostic Test or any cycle. 6. Inicia sesión para que tengamos en cuenta tu opinión. Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! Here is a link for the website: Sears Home Services . SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs.

If you remove any connectors, make sure you write down where they go. Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.