Home > Error Code > Kitchenaid Microwave Error Code F7

Kitchenaid Microwave Error Code F7

Contents

If damage is found, replace appropriate part. Other then that it usually takes a few seconds then F-7 error pops up. Plug in microwave oven or reconnect power.16. If problem persists, replace control assembly Posted on Jun 23, 2011 Helpful 0 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images this contact form

F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. It locked the key pad. Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Whirlpool Accuwave Microwave Oven Open Question F7 error message on whirlpool accuwave microwave

Kitchenaid Microwave Error Code F7

Jan 19, 2010 | Whirlpool Accuwave Microwave Oven 1 Answer F7 ERROR CODE ON GH6177XPS This is a known problem with this unit, and whirlpool has put out a Service Flash OK 2. The diodes are UXC2B diodes..

  1. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com « Replacing complete door assembly | Kenmore Quick Touch Microwave » Thread Tools Show Printable Version Email this
  2. ob - Off Balance - The lid switch must be opened at least once before reseting the cycle.
  3. Check wiring to the 1100W inverter and control system.6.
  4. Check voltage at 4903-1 on relay board.
  5. Hi my name isXXXXX will be assisting you with this problem.Please allow me some time to do research and type a response to each of your posts.The meaning of the error
  6. Check the resistance of the magnetron thermostat.
  7. Check the electronic controls. 6.

It was all good until I had drunk friends over, and that is when it happened. Floyd Kolb 43501 Answers SOURCE: Microwave Whirlpool accuwave still runs but does Hi, Here is a tip that will help you to figure out what is wrong with yourMicrowave Oven....Microwave Oven Ft.WhirlpoolGH5184XPT3MICROWAVE OVEN 1.8 Cu. Whirlpool Microwave Error Codes We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

The technician should perform the following procedure to test for an F7 error code: 1. Whirlpool Gold Accuwave Microwave Troubleshooting You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Possible reasons: 1. https://answers.yahoo.com/question/?qid=20090625233224AAvcoVw All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).

Check the P56/P66 connection between relay board and relay control board.8. Whirlpool Dishwasher F7 Error Code with 91% of all in-stock orders delivered within 2 business days. At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes. A video is available here showing how to remove a typical over the range control panel assembly in under 5 minutes.

Whirlpool Gold Accuwave Microwave Troubleshooting

Help Remember Me? http://www.justanswer.com/appliance/7ebj4-whirlpool-gold-microwave-f7-code-comes-caus.html If present, replace control board (clock). Kitchenaid Microwave Error Code F7 Close Yeah, keep it Undo Close This video is unavailable. Whirlpool Microwave Error Code F2 What is causing small holes on the siding on my house?

My AccountSearchMapsYouTubePlayNewsGmailDriveCalendarGoogle+TranslatePhotosMoreShoppingWalletFinanceDocsBooksBloggerContactsHangoutsEven more from GoogleSign inHidden fieldsSearch for groups or messages http://techkumar.com/error-code/3ds-max-error-code-126.html Loading... Check the MCU by looking for operations of the drive motor, and check drive motor for powered rotations. Posted on May 26, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images William Miller 8803 Answers SOURCE: Whirlpool MH1150XMS-3 Whirlpool Washer Error Code F7

If door is NOT latched, disconnect power from unit and check wires and connections. Trending Now Angelique Kerber Tom Brady Pilot Jones Adrienne Bailon 2016 Crossovers Auto Insurance Quotes Wendy Sabatini Jennifer Aniston Dating Sites Lauren Cohan Answers Relevance Rating Newest Oldest Best Answer: TOUCH Thousands of photos and diagrams make it very easy to find the right part. navigate here If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect. Lowes Without that essential information, I can only give more general advice. F6-E0 - Return Line Not Connected - This error should appear within 60 seconds after power up to appliance.

According to the technical sheet found hidden inside the unit behind the controller and online here:F7 Power to magnetron interrupted1.

Select 'cancel' and observe for one minute for errors. Replace all parts and panels before operating.19. Why would someone vacuum lime deposit debris out of their water heater? Unplug microwave oven or disconnect power.4.

FT.WhirlpoolGH8155XJQ0MICROWAVEWhirlpoolGH8155XJQ1MICROWAVE OVEN 1.5 CU. F7 �Microcomputer Board Failure: Change the microcomputer board. Other then that it usually takes a few seconds then F-7 error pops up. his comment is here Sign In   Sign In Remember me Not recommended on shared computers Sign In Forgot your password?

If this solves the problem A. If problem persists, unplug microwave oven or disconnect power.17. Appliance Princess 3,064 views 2:47 Whirlpool Microwave Disassembly – Microwave Repair Help - Duration: 15:02. F2-E5 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.

If one or more of the tests fail, "ERR " will be displayed.. 2.When a keypad is pressed, a number according to the test chart will be displayed. Not sure how to go about performing all the steps to test out the error. Copyright © 1999-2016 , Eldis Group Partnership. F1-E3 - Wiring Harness Cavity Size Does Not Match Stored Value - Check the jumpers in the harness to make sure they agree with the actual oven size.

Or just drag it here!