Home > Error Code > F27 Error Code Kenmore

F27 Error Code Kenmore

Contents

NOTE: The door switch/lock unit can be manually unlocked. Check wire harness connections to the pump and Central Control Unit (CCU). 3. Door switch/lock unit failure. 1. Replace Central Control Unit if drum is not moving. http://techkumar.com/error-code/kenmore-washer-error-code-f-26.html

Check for continuity of the User Interface harness. 2. on Jan 04, 2009 Helpful 32 Not Helpful 3 Comments Flag More Print this page Share this page 1 more comments Parker Oct 13, 2013 My problem started with a suds when i try to turn off the washer and restart it the same error comes up and the washer stops. Sign in to make your opinion count. http://www.shopyourway.com/questions/1087402

F27 Error Code Kenmore

Replace also the CCU. If you did not include a model # XXXXX your question please do on you second reply if possible,this helps us serve you faster.F27If there is too much water or foam Plug in washer or reconnect power. 6.

  • Check valve for continuity (abnormal = infi nity). 2.
  • Check door switch/lock unit. 3.
  • This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds.
  • Verify the shipping system including shipping bolts, spacers and cables are removed. 2.

F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1. Verify CCU operation by running a Diagnostic Test or any cycle. Perform test program. If the washer is still having a problem you likely need a new main control board.

F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. Whirlpool 6th Sense Washing Machine Error Codes Jen Russo 1,622 views 3:20 Whirlpool Duet Sport ht - F 21 error, will not drain. - Duration: 2:54. Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. http://www.justanswer.com/appliance/3s27a-f27-error-whirlpool-duet-washer.html Plug in washer or reconnect power. 5.

Verify inlet valve operation. Exchange the complete valve block if the steamer valve has not a resistance of approx. 812 Ω between both contacts. 6. Sign in to add this to Watch Later Add to Loading playlists... To unlock the door press PAUSE/CANCEL.Possible Causes/ProcedureCheck the drain hose and make sure it is not plugged or kinked.Unplug washer or disconnect power.Check wire harness connections to the drain pump, pressure

Whirlpool 6th Sense Washing Machine Error Codes

Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU).

Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect F27 Error Code Kenmore Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU).4. Whirlpool Front Load Washer Error Codes Check drain pump. 7.

NOTE: The door switch/lock unit can be manually unlocked. http://techkumar.com/error-code/204-error-code.html F2 - E0 Shorted keypad (also called touch pad) 1. My advice for that would be a Mossberg 500. Door switch open while door is locked. 1. Whirlpool Washer

Replace User Interface. F31 MCU FAILURE If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), Very good information by the way. http://techkumar.com/error-code/f20-error-code-kenmore-elite-washer.html If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the

Replace User Interface if drum is rotating. 4. Check doorswitch system. (See checklist of F26 and F29). Unplug washer or disconnect power. 3.

Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse,

F03 HEATER SC TO GROUND The Heater has a internal short circuit. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com #2 (permalink) 03-23-2011, 12:05 PM Joe / APP Team Senior Expert Join Date: Jul 2010 Ask Your Own Appliance Question Customer: replied6 years ago. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Removing the filter should remove all water from your washer. If you are using HE detergent, HOW MUCH are you using? The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω. his comment is here Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table.If resistance is 0 Ω or infi nite value, replace NTC.

rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. Check the connections between the Steamer 3. Plug in washer or reconnect power. 6. Replace heater.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...