Home > Error Code > Dell Hard Drive Error Codes

Dell Hard Drive Error Codes

Contents

This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Replace the drive. Check your floppy and retest. This may be due to a media or read/write error. http://techkumar.com/error-code/dell-error-code-0141-hard-drive.html

Check cabling and retest. Recheck your connections and replace the cable. This may be due to a media or read/write error. This may be due to a media or read/write error.

Dell Hard Drive Error Codes

All Rights Reserved. It also may be due to a defective connection. Drive Reliability Monitor.

The Identify Drive Command has not received an acceptable response from the drive. If ECC occurs, use Data Lifeguard for additional error correction. Retest. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.

There were media errors that were within the repair capabilities of diagnostic utility. Wd Error Codes May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. If the automatic repair feature is unable to repair these errors, replace the drive. Discover More Retest after checking the connections.

Replace the drive if the error repeats. This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition. If the error repeats, replace the drive. Ten or more instances of track information could not be found.

Wd Error Codes

Re-Test Drive 258 ECC 10+ Error Correction Code. https://hardforum.com/threads/wd-diagnostics-error-code-223.1300005/ The drive has not responded in the time allotted. Dell Hard Drive Error Codes No Errors 15 Read Diagnostics Sector Error A read command during the test has failed. Western Digital Error Code 0007 Replace the drive if the error repeats.

Replace your cable and retest. his comment is here If the error repeats, replace the drive. Re-test Drive with appropriate diagnostic utility 204 Missing Log File The log file that existed at startup of diagnostic utility has been moved or no longer exists. It may also be due to a defective connection. Seatools

  1. At least ten ECC errors have been detected.
  2. Re-Test Drive 116 IDNF Error Address Not Found Error.
  3. Drive should be replaced.
  4. Drive should be replaced.
  5. Drive should be replaced.
  6. Create and use a new DLG Tools diskette.
  7. There were too many errors found on this drive to be repaired.
  8. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.
  9. Drive should be replaced.
  10. Replace the drive.

Re-test Drive 138 Still Busy Timeout Timeout from checking busy bit. Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. http://techkumar.com/error-code/dell-error-code-2000-0141.html Check cabling and retest.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Replace Drive 227 SMART Not Supported Self-Monitoring, Analysis, and Reporting Technology (SMART) Certain older drives do not support SMART. The drive has failed and must be replaced.

Re-test with appropriate diagnostic utility 222 Drive Failed the Test The drive has failed the SMART test.

Retest after checking the connections. Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. Replace the drive if the error repeats. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer).

use the second link above to find the proper utility, or contact WD tech support if that fails... Replace the drive if the repair fails. Drive should be replaced. navigate here In order for S.M.A.R.T.

Re-Test Drive 11 Cable Test Failed Failure during cable test. Drive should be replaced. Check your connections and replace the cable. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives.

This may be due to a defect with the drive or a bad connection.